PriceList for 0.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA
PriceList for 0.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA Detail:
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting.
The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit.
| Type | Profiles | Abrasive Media Agent | Application |
| TAA-S#16 | ±100 micron | Aluminum Oxide#16 | Fast and aggressive for tough industrial coatings. |
| TAA-S#30 | ±75 micron | Aluminum Oxide#30 | Removal of multilayer coatings and profile to 75 micron. |
| TAA-S#30 | ±50 micron | Aluminum Oxide#80 | Effective for one or two laryers coatings and profile to50 micron. |
| TAA-S#30 | ±25 micron | Aluminum Oxide#120 | Effective on light and moderate rust, producing 25 micron profile. |
| TAA-S#30 | <25 micron | Aluminum Oxide#220 | For light coatings removal or to leave minor surface profiling. |
| TAA-G-40 | +100 micron | Steel Grit G40 | Removal the toughest coating. For surface preparation on deteriorated surfaces and for removing elastomeric or other extremely thich coatings. |
Features
1. Sponge media abrasives manufactured with polyurethane sponge is low breakage and longer lasting and could well suppress dust pollution which normally resulted from the abrasives breakage.
2. The sponge material absorbs the surface contaminants (mill scale, grease, etc) and thus improves the cleanness of the subject surface.
3. Worker safety is enhanced and risks such as eye and industrial injury is reduced due to low rebound of the porous sponge.
4. Less quality defects and low reworking
5. High quality surface treatment of sensitive and defined area
6. Coating lasting longer, reducing maintaining cost.
7. Recycling
8. Its sand blasting equipment is small in size and portable and suitable for surface cleaning of narrow area and special part.
9. This environment friendly, safe and high efficient new abrasive brings about clean, quite and visible work sites.
Operating principle
1. Dual-component sponge media abrasive are propoed to the surface using an air-doven system
2. Blasting of sponge media abrasive
* Absorb collision energy, flattened and suppress the release of loosened surface contaminants
* Expose the abrasive, remove surface contanη inants
3. When leaving the surface, the Sponge media abrasives expands back to normal size creating a vacuum which absorbs most of the dusts and contaminants
Applications
Widely used in Marine, Offshore Engineering, Military, Petrochemical Project, Aerospace & Aviation, Nuclear Power, Historic Restoration, Wall Cleaning, Building Maintenance etc.
Product detail pictures:
Related Product Guide:
We generally continually give you quite possibly the most conscientious shopper company, and the widest variety of designs and styles with finest materials. These endeavours include the availability of customized designs with speed and dispatch for PriceList for 0.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA , The product will supply to all over the world, such as: Kenya, Guyana, Pakistan, After years of development, we have formed strong ability in new product development and strict quality control system to ensure excellent quality and service. With the support of many long term cooperated customers, our products are welcomed all over the world.
By Juliet from Latvia - 2017.04.18 16:45
The factory technical staff gave us a lot of good advice in the cooperation process, this is very good, we are very grateful.
By Irma from Hyderabad - 2017.05.02 11:33
Related products
-
8 Year Exporter Chilled Steel Shot S280 0.8mm -...
Product feature High strengthen, high tenacity, long service life. Low breakage, low dust, low pollution. Low wear of the equipments, long life of accessory. Reduce dedusting system load, lengthen usage time of dedusting equipments. Technical specification Chemical Composition% C 0.10-0.20% Si 0.10-0.35% Mn 0.35-1.50% S ≤0.05% P ≤0.05% Other alloy elements Adding Cr Mo Ni B Al Cu etc. Hardness HRC42-48/48-54 Microstructure Duple...
-
Personlized Products Brown Fused Alumina Oxidee...
Available Hardness: GP: HRC46-50 Newly made products with angular, the grit are gradually rounded off in use and its particularly suited for oxide skin pre-treatment. GL: HRC56-60 Harder than GP steel grit, also loses its sharp edges during shot basting and is particularly suited to surface preparation applications. GH: HRC63-65 High hardness, sharp edges remain during operation, mainly used for compressed air shot blasting equipment. Production Strength: TAA adopts Arc Furnace Smelting an...
-
Hot-selling Steel Shot S110 - Zinc cut wire &#...
Made from high grade zinc wire, produced by cutting zinc wire into pellets, the length equal to the diameter of the wire. Zinc Cut Wire is also available in a conditioned form which is used as a longer lasting alternative to cast zinc shot. These are ideal for deflashing and finishing die castings, normally in wheel blast equipment. Available at competent rates, our products reduce wear and tear on blast equipment compared to most other metallic abrasives. Features 1. Bright colour and ...
-
Bottom price Glass Bead Blasting Aluminum - Lo...
Product feature High strengthen, high tenacity, long service life. Low breakage, low dust, low pollution. Low wear of the equipments, long life of accessory. Reduce dedusting system load, lengthen usage time of dedusting equipments. Technical specification Chemical Composition% C 0.10-0.20% Si 0.10-0.35% Mn 0.35-1.50% S ≤0.05% P ≤0.05% Other alloy elements Adding Cr Mo Ni B Al Cu etc. Hardness HRC42-48/48-54 Microstructure Duplex structure co...
-
Factory directly supply Stainless Steel Shot Bl...
Compared with traditional steel grit made by crushing steel shot, bearing steel grit has the following Features: Raw Material Bearing steel grit is made by Chromium bearing steel which has good harden ability due to its high content of Chromium. Technology Bearing steel grit is made by crushing the forged bearing steel directly which is free from casting defects. Low wear The forged state bearing steel grit with sharp edges has higher mechanical property than traditional cast steel gr...
-
Factory Cheap Hot Tungsten Carbide Grinding Dis...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
