Factory Outlets Cutting Disc In Face - Cutting disc FS-03 series – TAA
Factory Outlets Cutting Disc In Face - Cutting disc FS-03 series – TAA Detail:
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diamond tools.
Advantages
Safty and environment friendly
Fast cutting and grinding,no break off,no pollution
· High efficiency
Improving efficiency of 30%-50% than traditional cutting disk
· Long service life
Using brazing technology,diamond on the surface not falling down
TAA diamond cutting disc
| Number | Picture | Specification | Safety Rotary Speed(r/min) | Application | Performance comparisons |
| FS100-03 |  |
100×1.2×16/20 | 12000 | Cutting of hard and brittle materials such as iron casting (ductile cast iron, Gray Cast iron and all kinds of iron), marble, fiber glass, ceramic tile, refractory material. Round cutter disk cut more smooth, kerf is flat. | 1. Cutting cast iron parts risers,the life of TAA is over 70 times than resin disk, efficiency increased by 100%. 2. Cutting marble area, the life of TAA is 3 times than sintered cutter disk , efficiency increased by 35%. 3. Cutting steel plate-concrete structure, the life of TAA is 100 times than resin cutting disk , efficiency is 3.5 times than resincutting disk. 4. Cutting fiber glass,the life of TAA is 100 times than resin cutter disk , efficiency increased by100%. |
| FS125-03 | 125×1.5×22.23 | 10000 | |||
| FS150-03 | 150×1.5×22.23 | 9500 | |||
| FS180-03 | 180×1.6×22.23/25.4 | 8500 | |||
| FS230-03 | 230×1.6×22.23/25.4 | 6000 | |||
| FS350-05 |  |
350×2.4X32 | 4500 | ||
| FS400-05 | 400×2.5X32 | 4000 |
Product detail pictures:
Related Product Guide:
To get the stage of realizing dreams of our employees! To build a happier, more united and much more skilled crew! To reach a mutual benefit of our prospects, suppliers, the society and ourselves for Factory Outlets Cutting Disc In Face - Cutting disc FS-03 series – TAA , The product will supply to all over the world, such as: Greece, Florida, Brunei, If you are interested in any of our products and solutions or would like to discuss a custom order, remember to feel free to contact us. We are looking forward to forming successful business relationships with new clients around the world in the near future.
By Elizabeth from Qatar - 2018.02.12 14:52
Company director has very rich management experience and strict attitude, sales staff are warm and cheerful, technical staff are professional and responsible,so we have no worry about product,a nice manufacturer.
By Maxine from Lyon - 2017.05.31 13:26
Related products
-
Factory making Gp80 Bearing Steel Grit - Beari...
Compared with traditional steel grit made by crushing steel shot, bearing steel grit has the following Features: Raw Material Bearing steel grit is made by Chromium bearing steel which has good harden ability due to its high content of Chromium. Technology Bearing steel grit is made by crushing the forged bearing steel directly which is free from casting defects. Low wear The forged state bearing steel grit with sharp edges has higher mechanical property than traditional cast steel gr...
-
Good Wholesale Vendors Brown Fused Alumina Dens...
Available Hardness: GP: HRC46-50 Newly made products with angular, the grit are gradually rounded off in use and its particularly suited for oxide skin pre-treatment. GL: HRC56-60 Harder than GP steel grit, also loses its sharp edges during shot basting and is particularly suited to surface preparation applications. GH: HRC63-65 High hardness, sharp edges remain during operation, mainly used for compressed air shot blasting equipment. Production Strength: TAA adopts Arc Furnace Smelti...
-
China wholesale Cast Alloy Shot - Steel Shot &...
Chemical Composition C 0.85-1.20% Si 0.40-1.20% Mn 0.60-1.20% S ≤0.05% P ≤0.05% Hardness HRC 40-50 Microstructure Homogeneous Tempered Martensite or Troostite Density ≥ 7.2g/cm3 External form Spherical Hollow particles<10% Size distribution Screen No. Inch Screen size S70 S110 S170 S230 S280 S330 S390 S460 S550 S660 S780 S930 6 0.132 3.35 All pass 7 0.111 2.80 All pass 8 0.0937 2.36 All...
-
Fixed Competitive Price 430 1.2mm Stainless Ste...
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting. The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit. Type Profiles Abrasive Media Agent Application TAA-S#16 ±100 micron Aluminum Oxide#16 Fast and aggressive for tough industrial coatings. TAA-S#30 ±75 micron Aluminum Oxide#30 Removal of multilayer coatings and profile to 75 micron. TAA-S#30 ±50 micro...
-
Popular Design for Pin On Aluminum Cut Wire - ...
Advantage ■ clean and smooth, not hurt to the mechanical precision of work piece. ■ high mechanical intensity, hardness, flexibility ■ it can be reused several times, the same effect and is not easily broken. ■ uniform size, after blasting sand around the device to maintain a uniform brightness effect, not easy to leave a watermark. ■ high purity and good quality meet the international standard. ■ stable chemistry property, not pollute the metal processed. Technical specification Chemica...
-
Reasonable price for Mesh Garnet Abrasive - Co...
Tech Data Product Description Copper Cut Wire Shot Chemical Composition Cu: 58-99%, the rest is Zn Microhardness 110~300HV Tensile Intensity 200~500Mpa Durability 5000 Times Microstructure Deformed αorα+β Density 8.9 g/cm3 Bulk Density 5.1 g/cm3 Available sizes: 1.0mm, 1.5mm, 2.0mm, 2.5mm etc. Advantage 1. Long life time 2. Less Dust 3. Specific gravity higher than other blasting beads 4. Lower hardness than steel shot &glass beads 5. Sh...
