Good quality The Copper Shot - Sponge media abrasives – TAA
Good quality The Copper Shot - Sponge media abrasives – TAA Detail:
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting.
The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit.
| Type | Profiles | Abrasive Media Agent | Application |
| TAA-S#16 | ±100 micron | Aluminum Oxide#16 | Fast and aggressive for tough industrial coatings. |
| TAA-S#30 | ±75 micron | Aluminum Oxide#30 | Removal of multilayer coatings and profile to 75 micron. |
| TAA-S#30 | ±50 micron | Aluminum Oxide#80 | Effective for one or two laryers coatings and profile to50 micron. |
| TAA-S#30 | ±25 micron | Aluminum Oxide#120 | Effective on light and moderate rust, producing 25 micron profile. |
| TAA-S#30 | <25 micron | Aluminum Oxide#220 | For light coatings removal or to leave minor surface profiling. |
| TAA-G-40 | +100 micron | Steel Grit G40 | Removal the toughest coating. For surface preparation on deteriorated surfaces and for removing elastomeric or other extremely thich coatings. |
Features
1. Sponge media abrasives manufactured with polyurethane sponge is low breakage and longer lasting and could well suppress dust pollution which normally resulted from the abrasives breakage.
2. The sponge material absorbs the surface contaminants (mill scale, grease, etc) and thus improves the cleanness of the subject surface.
3. Worker safety is enhanced and risks such as eye and industrial injury is reduced due to low rebound of the porous sponge.
4. Less quality defects and low reworking
5. High quality surface treatment of sensitive and defined area
6. Coating lasting longer, reducing maintaining cost.
7. Recycling
8. Its sand blasting equipment is small in size and portable and suitable for surface cleaning of narrow area and special part.
9. This environment friendly, safe and high efficient new abrasive brings about clean, quite and visible work sites.
Operating principle
1. Dual-component sponge media abrasive are propoed to the surface using an air-doven system
2. Blasting of sponge media abrasive
* Absorb collision energy, flattened and suppress the release of loosened surface contaminants
* Expose the abrasive, remove surface contanη inants
3. When leaving the surface, the Sponge media abrasives expands back to normal size creating a vacuum which absorbs most of the dusts and contaminants
Applications
Widely used in Marine, Offshore Engineering, Military, Petrochemical Project, Aerospace & Aviation, Nuclear Power, Historic Restoration, Wall Cleaning, Building Maintenance etc.
Product detail pictures:
Related Product Guide:
"Sincerity, Innovation, Rigorousness, and Efficiency" may be the persistent conception of our organization for that long-term to establish jointly with customers for mutual reciprocity and mutual gain for Good quality The Copper Shot - Sponge media abrasives – TAA , The product will supply to all over the world, such as: Armenia, Portland, Mecca, We hope we can establish long-term cooperation with all of the customers, and hope we can improve competitiveness and achieve the win-win situation together with the customers. We sincerely welcome the customers from all over the world to contact us for anything you need!Welcome all customers both at home and abroad to visit our factory. We hope to have win-win business relationships with you, and create a better tomorrow.
By Steven from Russia - 2017.07.07 13:00
The enterprise has a strong capital and competitive power, product is sufficient, reliable, so we have no worries on cooperating with them.
By Gary from Sudan - 2017.08.15 12:36
Related products
-
Factory wholesale Aluminum Cut Wire 0.6mm - Co...
Tech Data Product Description Copper Cut Wire Shot Chemical Composition Cu: 58-99%, the rest is Zn Microhardness 110~300HV Tensile Intensity 200~500Mpa Durability 5000 Times Microstructure Deformed αorα+β Density 8.9 g/cm3 Bulk Density 5.1 g/cm3 Available sizes: 1.0mm, 1.5mm, 2.0mm, 2.5mm etc. Advantage 1. Long life time 2. Less Dust 3. Specific gravity higher than other blasting beads 4. Lower hardness than steel shot &glass b...
-
2018 High quality Double Disc Grinding - Grind...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
-
Factory Supply Blasting Using Glass Beads - Ca...
We made great improvement in material and the techniques on the basis of the traditional production process. Utilizing high quality alloy steel wire as the substrate that higher the mechanical properties and make it more stable. Improving the wiredrawing craft which make the internal organization more dense. Improving the traditional passivation process that completely relying on impacting to reduce the damage during blasting, enhancing the service life. Item Technical index Chemi...
-
Top Quality 150# Brown Fused Alumina - Garnet ...
Features ■ Low Dust—The high intrinsic tenacity and a high proportion of the material itself fast the settlement rate and significantly reduce the dust emissions and dust coming from the workpiece, minimizing cleaning effort sandblasting, reducing pollution of the work area. ■ Excellent Surface Quality—It can deep into the voids and uneven parts to clean, thereby completely remove rust, soluble salts and other contaminants; surface blasting process without inserts, will not advers...
-
China Gold Supplier for Sponge Jet Media Blasti...
Product feature High strengthen, high tenacity, long service life. Low breakage, low dust, low pollution. Low wear of the equipments, long life of accessory. Reduce dedusting system load, lengthen usage time of dedusting equipments. Technical specification Chemical Composition% C 0.10-0.20% Si 0.10-0.35% Mn 0.35-1.50% S ≤0.05% P ≤0.05% Other alloy elements Adding Cr Mo Ni B Al Cu etc. Hardness HRC42-48/48-54 Microstructure Duplex structure co...
-
Short Lead Time for Mini Grinder Cutting Discs ...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
