OEM/ODM China Ervin Stainless Steel Grit - Sponge media abrasives – TAA
OEM/ODM China Ervin Stainless Steel Grit - Sponge media abrasives – TAA Detail:
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting.
The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit.
| Type | Profiles | Abrasive Media Agent | Application |
| TAA-S#16 | ±100 micron | Aluminum Oxide#16 | Fast and aggressive for tough industrial coatings. |
| TAA-S#30 | ±75 micron | Aluminum Oxide#30 | Removal of multilayer coatings and profile to 75 micron. |
| TAA-S#30 | ±50 micron | Aluminum Oxide#80 | Effective for one or two laryers coatings and profile to50 micron. |
| TAA-S#30 | ±25 micron | Aluminum Oxide#120 | Effective on light and moderate rust, producing 25 micron profile. |
| TAA-S#30 | <25 micron | Aluminum Oxide#220 | For light coatings removal or to leave minor surface profiling. |
| TAA-G-40 | +100 micron | Steel Grit G40 | Removal the toughest coating. For surface preparation on deteriorated surfaces and for removing elastomeric or other extremely thich coatings. |
Features
1. Sponge media abrasives manufactured with polyurethane sponge is low breakage and longer lasting and could well suppress dust pollution which normally resulted from the abrasives breakage.
2. The sponge material absorbs the surface contaminants (mill scale, grease, etc) and thus improves the cleanness of the subject surface.
3. Worker safety is enhanced and risks such as eye and industrial injury is reduced due to low rebound of the porous sponge.
4. Less quality defects and low reworking
5. High quality surface treatment of sensitive and defined area
6. Coating lasting longer, reducing maintaining cost.
7. Recycling
8. Its sand blasting equipment is small in size and portable and suitable for surface cleaning of narrow area and special part.
9. This environment friendly, safe and high efficient new abrasive brings about clean, quite and visible work sites.
Operating principle
1. Dual-component sponge media abrasive are propoed to the surface using an air-doven system
2. Blasting of sponge media abrasive
* Absorb collision energy, flattened and suppress the release of loosened surface contaminants
* Expose the abrasive, remove surface contanη inants
3. When leaving the surface, the Sponge media abrasives expands back to normal size creating a vacuum which absorbs most of the dusts and contaminants
Applications
Widely used in Marine, Offshore Engineering, Military, Petrochemical Project, Aerospace & Aviation, Nuclear Power, Historic Restoration, Wall Cleaning, Building Maintenance etc.
Product detail pictures:
Related Product Guide:
We've got a really efficient group to deal with inquiries from prospects. Our purpose is "100% customer fulfillment by our product excellent, price & our group service" and enjoy a superb track record amid clientele. With many factories, we can easily deliver a wide selection of OEM/ODM China Ervin Stainless Steel Grit - Sponge media abrasives – TAA , The product will supply to all over the world, such as: Cyprus, Philippines, Mecca, Our organization. Situated inside the national civilized cities, the visitors is very easy, unique geographical and economic situations. We pursue a "people-oriented, meticulous manufacturing, brainstorm, construct brilliant" organization. hilosophy. Strict top quality management, fantastic service, reasonable cost in Myanmar is our stand on the premise of competition. If vital, welcome to make contact with us by our web page or telephone consultation, we've been likely to be pleased to serve you.
By Dee Lopez from Kuwait - 2017.11.11 11:41
This manufacturers not only respected our choice and requirements, but also gave us a lot of good suggestions, ultimately， we successfully completed the procurement tasks.
By Bertha from Liverpool - 2018.11.22 12:28
Related products
-
Factory directly supply Stainless Steel Shot Bl...
Chemical Composition C 0.85-1.20% Si 0.40-1.20% Mn 0.60-1.20% S ≤0.05% P ≤0.05% Hardness HRC 40-50 Microstructure Homogeneous Tempered Martensite or Troostite Density ≥ 7.2g/cm3 External form Spherical Hollow particles<10% Size distribution Screen No. Inch Screen size S70 S110 S170 S230 S280 S330 S390 S460 S550 S660 S780 S930 6 0.132 3.35 All pass 7 0.111 2.80 All pass 8 0.0937 2.36 All pass ≥90% 10 0.0787 2.00 All pa...
-
Renewable Design for S390 Low Carbon Steel Shot...
We made great improvement in material and the techniques on the basis of the traditional production process. Utilizing high quality alloy steel wire as the substrate that higher the mechanical properties and make it more stable. Improving the wiredrawing craft which make the internal organization more dense. Improving the traditional passivation process that completely relying on impacting to reduce the damage during blasting, enhancing the service life. Item Technical index Chemi...
-
Low MOQ for Cut Off Wheel Grit - Grinding whee...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
-
Rapid Delivery for Side Plate - Hanger type sh...
As a rule, hanger-type blast machines are offered either for batch or continuous processing. However, there are many intermediate designs that are oriented towards different kinds of overhead conveyor systems. In many cases, different processes such as blasting, painting and subsequent drying can be interconnected via the overhead conveyor system. This makes it possible to tap an enormous potential for streamlining the process workflow. Additional processing variants are created by using diff...
-
OEM/ODM China Steel Shot Price - Sponge media ...
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting. The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit. Type Profiles Abrasive Media Agent Application TAA-S#16 ±100 micron Aluminum Oxide#16 Fast and aggressive for tough industrial coatings. TAA-S#30 ±75 micron Aluminum Oxide#30 Removal of multilayer coatings and profile to 75 micron. TAA-S#30 ±50 micro...
-
Top Suppliers Stainless Steel Cut Wire Shot 0.4...
Features * Can be used to replace a variety of mineral sands & non-metallic abrasives,such as corundum, silicon carbide, arenaceous quartz, glass beads, etc. * Low dust emissions,improving operating environment, environmental friendly. * Can replace part of the pickling process. * Low dust emission and excellent operating environment, reducing the treatment of pickling waste. * Low comprehensive cost, the service life is 30-100 times that of non-metallic abrasive such as corundum. * ...
