Popular Design for 410 1.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA
Popular Design for 410 1.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA Detail:
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting.
The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit.
| Type | Profiles | Abrasive Media Agent | Application |
| TAA-S#16 | ±100 micron | Aluminum Oxide#16 | Fast and aggressive for tough industrial coatings. |
| TAA-S#30 | ±75 micron | Aluminum Oxide#30 | Removal of multilayer coatings and profile to 75 micron. |
| TAA-S#30 | ±50 micron | Aluminum Oxide#80 | Effective for one or two laryers coatings and profile to50 micron. |
| TAA-S#30 | ±25 micron | Aluminum Oxide#120 | Effective on light and moderate rust, producing 25 micron profile. |
| TAA-S#30 | <25 micron | Aluminum Oxide#220 | For light coatings removal or to leave minor surface profiling. |
| TAA-G-40 | +100 micron | Steel Grit G40 | Removal the toughest coating. For surface preparation on deteriorated surfaces and for removing elastomeric or other extremely thich coatings. |
Features
1. Sponge media abrasives manufactured with polyurethane sponge is low breakage and longer lasting and could well suppress dust pollution which normally resulted from the abrasives breakage.
2. The sponge material absorbs the surface contaminants (mill scale, grease, etc) and thus improves the cleanness of the subject surface.
3. Worker safety is enhanced and risks such as eye and industrial injury is reduced due to low rebound of the porous sponge.
4. Less quality defects and low reworking
5. High quality surface treatment of sensitive and defined area
6. Coating lasting longer, reducing maintaining cost.
7. Recycling
8. Its sand blasting equipment is small in size and portable and suitable for surface cleaning of narrow area and special part.
9. This environment friendly, safe and high efficient new abrasive brings about clean, quite and visible work sites.
Operating principle
1. Dual-component sponge media abrasive are propoed to the surface using an air-doven system
2. Blasting of sponge media abrasive
* Absorb collision energy, flattened and suppress the release of loosened surface contaminants
* Expose the abrasive, remove surface contanη inants
3. When leaving the surface, the Sponge media abrasives expands back to normal size creating a vacuum which absorbs most of the dusts and contaminants
Applications
Widely used in Marine, Offshore Engineering, Military, Petrochemical Project, Aerospace & Aviation, Nuclear Power, Historic Restoration, Wall Cleaning, Building Maintenance etc.
Product detail pictures:
Related Product Guide:
We emphasize progress and introduce new merchandise into the market each and every year for Popular Design for 410 1.2mm Stainless Steel Cut Wire Shot - Sponge media abrasives – TAA , The product will supply to all over the world, such as: Israel, Malaysia, Ecuador, We'd like to invite customers from abroad to discuss business with us. We can provide our clients with high quality products and excellent service. We are sure that we will have good cooperative relationships and make a brilliant future for both parties.
By Hulda from Oman - 2018.12.25 12:43
Customer service staff and sales man are very patience and they all good at English, product's arrival is also very timely, a good supplier.
By April from United States - 2017.11.01 17:04
Related products
-
Low price for Copper Shot Sand Blasting - Stai...
Features * Can be used to replace a variety of mineral sands & non-metallic abrasives,such as corundum, silicon carbide, arenaceous quartz, glass beads, etc. * Low dust emissions,improving operating environment, environmental friendly. * Can replace part of the pickling process. * Low dust emission and excellent operating environment, reducing the treatment of pickling waste. * Low comprehensive cost, the service life is 30-100 times that of non-metallic abrasive such as corundum. * Can B...
-
Good Quality Cut Wire Zinc Shot - Low Carbon S...
Product feature High strengthen, high tenacity, long service life. Low breakage, low dust, low pollution. Low wear of the equipments, long life of accessory. Reduce dedusting system load, lengthen usage time of dedusting equipments. Technical specification Chemical Composition% C 0.10-0.20% Si 0.10-0.35% Mn 0.35-1.50% S ≤0.05% P ≤0.05% Other alloy elements Adding Cr Mo Ni B Al Cu etc. Hardness HRC42-48/48-54 Microstructure Duplex structure co...
-
China New Product Cut Off Wheel Aluminum - Gri...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
-
Lowest Price for Cutting Disc 7inch - Cutting ...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
-
OEM Manufacturer Soft Sponge Media - Garnet &#...
Features ■ Low Dust—The high intrinsic tenacity and a high proportion of the material itself fast the settlement rate and significantly reduce the dust emissions and dust coming from the workpiece, minimizing cleaning effort sandblasting, reducing pollution of the work area. ■ Excellent Surface Quality—It can deep into the voids and uneven parts to clean, thereby completely remove rust, soluble salts and other contaminants; surface blasting process without inserts, will not advers...
-
Special Design for Brown Fused Alumina 70# - G...
Advantage ■ clean and smooth, not hurt to the mechanical precision of work piece. ■ high mechanical intensity, hardness, flexibility ■ it can be reused several times, the same effect and is not easily broken. ■ uniform size, after blasting sand around the device to maintain a uniform brightness effect, not easy to leave a watermark. ■ high purity and good quality meet the international standard. ■ stable chemistry property, not pollute the metal processed. Technical specification Chemica...
