Super Lowest Price G80 Stainless Steel Grit - Sponge media abrasives – TAA
Super Lowest Price G80 Stainless Steel Grit - Sponge media abrasives – TAA Detail:
Sponge Media abrasive are available in over 20 types,achieving profiles from 0 to 100+ micron. All procides dry, low dust, low rebound blasting.
The most commomly used is TAA-S series with aluminum oxide and TAA-G series with steel grit.
| Type | Profiles | Abrasive Media Agent | Application |
| TAA-S#16 | ±100 micron | Aluminum Oxide#16 | Fast and aggressive for tough industrial coatings. |
| TAA-S#30 | ±75 micron | Aluminum Oxide#30 | Removal of multilayer coatings and profile to 75 micron. |
| TAA-S#30 | ±50 micron | Aluminum Oxide#80 | Effective for one or two laryers coatings and profile to50 micron. |
| TAA-S#30 | ±25 micron | Aluminum Oxide#120 | Effective on light and moderate rust, producing 25 micron profile. |
| TAA-S#30 | <25 micron | Aluminum Oxide#220 | For light coatings removal or to leave minor surface profiling. |
| TAA-G-40 | +100 micron | Steel Grit G40 | Removal the toughest coating. For surface preparation on deteriorated surfaces and for removing elastomeric or other extremely thich coatings. |
Features
1. Sponge media abrasives manufactured with polyurethane sponge is low breakage and longer lasting and could well suppress dust pollution which normally resulted from the abrasives breakage.
2. The sponge material absorbs the surface contaminants (mill scale, grease, etc) and thus improves the cleanness of the subject surface.
3. Worker safety is enhanced and risks such as eye and industrial injury is reduced due to low rebound of the porous sponge.
4. Less quality defects and low reworking
5. High quality surface treatment of sensitive and defined area
6. Coating lasting longer, reducing maintaining cost.
7. Recycling
8. Its sand blasting equipment is small in size and portable and suitable for surface cleaning of narrow area and special part.
9. This environment friendly, safe and high efficient new abrasive brings about clean, quite and visible work sites.
Operating principle
1. Dual-component sponge media abrasive are propoed to the surface using an air-doven system
2. Blasting of sponge media abrasive
* Absorb collision energy, flattened and suppress the release of loosened surface contaminants
* Expose the abrasive, remove surface contanη inants
3. When leaving the surface, the Sponge media abrasives expands back to normal size creating a vacuum which absorbs most of the dusts and contaminants
Applications
Widely used in Marine, Offshore Engineering, Military, Petrochemical Project, Aerospace & Aviation, Nuclear Power, Historic Restoration, Wall Cleaning, Building Maintenance etc.
Product detail pictures:
Related Product Guide:
Along with the "Client-Oriented" enterprise philosophy, a rigorous high-quality control process, superior production products along with a robust R&D group, we constantly deliver premium quality products, exceptional solutions and aggressive costs for Super Lowest Price G80 Stainless Steel Grit - Sponge media abrasives – TAA , The product will supply to all over the world, such as: Juventus, Mauritius, Costa rica, Our Company policy is "quality first, to be better and stronger, sustainable development" . Our pursuit goals is "for society, customers, employees, partners and enterprises to seek reasonable benefit". We aspirate to do cooperate with all different the auto parts manufacturers, repair shop, auto peer , then create a beautiful future! Thank you for taking time to browse our website and we would welcome any suggestions you may have that can help us to improve our site.
By Sally from Argentina - 2017.01.11 17:15
Production management mechanism is completed, quality is guaranteed, high credibility and service let the cooperation is easy, perfect!
By Elsie from Macedonia - 2018.05.22 12:13
Related products
-
Short Lead Time for S280 Low Carbon Steel Shot ...
Made from high grade zinc wire, produced by cutting zinc wire into pellets, the length equal to the diameter of the wire. Zinc Cut Wire is also available in a conditioned form which is used as a longer lasting alternative to cast zinc shot. These are ideal for deflashing and finishing die castings, normally in wheel blast equipment. Available at competent rates, our products reduce wear and tear on blast equipment compared to most other metallic abrasives. Features 1. Bright colour and ...
-
Bottom price Sand Blasting Copper Cut Wire Shot...
Compared with traditional steel grit made by crushing steel shot, bearing steel grit has the following Features: Raw Material Bearing steel grit is made by Chromium bearing steel which has good harden ability due to its high content of Chromium. Technology Bearing steel grit is made by crushing the forged bearing steel directly which is free from casting defects. Low wear The forged state bearing steel grit with sharp edges has higher mechanical property than traditional cast steel gr...
-
Factory source Stainless Steel Cut Wire Shot 0....
Product feature High strengthen, high tenacity, long service life. Low breakage, low dust, low pollution. Low wear of the equipments, long life of accessory. Reduce dedusting system load, lengthen usage time of dedusting equipments. Technical specification Chemical Composition% C 0.10-0.20% Si 0.10-0.35% Mn 0.35-1.50% S ≤0.05% P ≤0.05% Other alloy elements Adding Cr Mo Ni B Al Cu etc. Hardness HRC42-48/48-54 Microstructure Duplex structure co...
-
Good User Reputation for Diamond Blade For Cutt...
Our super-hard alloy tools are produced by brazing. Under certain conditions, a layer of diamond is firmly welded to the metal substrate after a metal solder melting process. This type of product has the characteristics of high grinding efficiency, long service life, safety, environmental protection and pollution-free. Mainly replace the current resin bond corundum cutting and polishing tools, all coarse and medium coarse-grained electroplated diamond tools, and some hot-pressed sintered diam...
-
Hot sale Blasting Glass Beads - Aluminum cut w...
Aluminum cut wire shot also named as aluminum shot,aluminum beads, aluminum granules, aluminum pellet. It is made from superior quality aluminum wire, appearance is bright, is an ideal media for cleaning and reinforcing the surface of nonferrous metal casting parts. It’s mainly applied for the surface treatment of Aluminum, Zinc products or work pieces with thin wall in shot blasting machine. Tech Data Products Aluminium Cut Wire Shot Chemical Composition Al≥99% Microhar...
-
China Cheap price Gl25 Bearing Steel Grit - Br...
Features Alumina oxide abrasive have high hardness and sharp angular, is widely used for both wet and dry blasting, creating the suitable profile for surface preparation. Alumina oxide abrasive is an idea blasting abrasive media for surface preparation requesting ferrous free. Alumina oxide abrasive is high efficiency blasting abrasives with sharp edges and high density. It is reusable and can be used in different types of blasting machine. Technical specification Type It...
